Xerox WIDE FORMAT 721P Operator'S Manual Download Page 21

Page: 21 / 72

PRINTER OVERVIEW

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

Operator Panel & Status Display

The operator panel is located on top of the front side of the printer.
It consists of a graphic display, a message display and several
function keys.

1. Ready Indicator

Flashes when the printer is warming up, and remains on steady
when the printer is ready to operate.

2. Door Open Indicator

This indicator flashes and an error code is displayed when a door
is opened, or the Inner Transport Unit is opened.

3. Toner Empty Indicator

This indicator flashes when the toner level is low.
When the toner supply is empty, the indicator is on steady and no
more prints can be made.
You can replace the Toner cartridge even if the printer is
operating.

4. Media Empty Indicator

This indicator flashes when the selected media roll is depleted.

5. Media Jam Indicator

This indicator flashes when media is jammed in the printer.

6. Wire-Clean key

The Charge Scorotron Wire is cleaned when this key is pressed.
The Ready Indicator flashes during the cleaning process.

7. Exp-Clean key

Lens Array of LED Print Head is cleaned when this button is
pressed. Ready Indicator flashes during the cleaning process.

8. Media Roll Indicator

Displays the selected media roll for lead edge cut when the
SELECT key is pressed.

9. Select key

Press this key to select the media roll desired for a lead edge cut.

10. Cut key

Press this key to feed and cut 240mm of the lead edge of the
selected roll.

11. Media Jam Location
Indicator

Indicates the location where Jam has occurred.

12. Copy Density Indicator

The selected Print Density level is illuminated.

13. Copy Density Key

Use this key to temporarily increase or decrease the image
density.

Menu,

, *, Enter,

Online

These keys are used for changing User Modes described in
Chapter 7. The Online Key is also used to place the printer Offline
and Online.

15. Status Display

Error Codes, Status Codes and messages are displayed here.

Exp-Clean

Wire-Clean

Paper Deck

1 2 3 4

Select

Cut

Exit

Copy Density

Enter

Online

3 4

Summary of Contents for WIDE FORMAT 721P









































































Search results

Summary of Contents for WIDE FORMAT 721P

Reviews:

Related manuals for WIDE FORMAT 721P

Brands by name

Popular brands

Xerox WIDE FORMAT 721P, Operator'S Manual

Search results

Summary of Contents for WIDE FORMAT 721P

Reviews:

Related manuals for WIDE FORMAT 721P

Brands by name

Popular brands