Xerox Phaser 3020 Service Manual Download Page 92 | Manualshive

Page: 92 / 116

background image

June 2014

6-6

Xerox® Phaser® 3020 Printer Service Manual

System Overview

General Procedures and Information

Drives

The Drive System consists of the Main (BLDC) Motor, Registration and Pick-up Clutches along
with various gears for the Drum Cartridge (OPC), Fuser, Pick-up, Registration, Feed and Exit
Rollers.

Toner System

The Phaser® 3020 printer uses a integrated toner system. The toner cartridge, photoreceptor
and developer units are contained within the Print Cartridge.

Figure 5 Integrated Toner System

«
...
90
91
92
93
94
...
»

Summary of Contents for Phaser 3020





















































































































Reviews:

No comments

Related manuals for Phaser 3020

Brand: Oki Pages: 24

Brand: VAF instruments Pages: 24

Brand: 3DP Pages: 12

Brand: Oki Pages: 8

Brand: Oki Pages: 48

Stylus Pro 7900

Brand: X-Rite Pages: 36

Brand: NCR Pages: 2

Brand: Canon Pages: 4

Brand: VASTEX Pages: 12

Brand: FOREVER Pages: 2

Brand: Xiamen Hanin Electronic Technology Pages: 27

Brand: LaserLine Pages: 14

Brand: Xerox Pages: 233

Brand: Delta OHM Pages: 28

4400B - Phaser B/W Laser Printer

Brand: Xerox Pages: 24

Brand: Kyocera Pages: 72

Brand: Oce Pages: 495

VersaLink C9000

Brand: Xerox Pages: 255

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands