Xerox Phaser 3020 Service Manual Download Page 8 | Manualshive

Page: 8 / 116

Xerox Phaser 3020 Service Manual Download Page 8

June 2014

iv

Xerox® Phaser® 3020 Printer Service Manual

Introduction

How to Use this Manual

Always start with Service Call Procedures, Section 1. Perform Initial Actions and verify the
problem, then follow the directions given.

How to Differentiate Between Machine Variants

The machine configuration will be identified in this manual by the configuration identifier
3020BI.

The Phaser® 3020 is Blue Angel certified with software configuration for up to 29 ppm capabil-
ity. Refer to the User Guide, Parts List and Procedures for information specific to printer config-
uration.

When a procedure, parts list description or other reference is unique amongst different configu-
rations of the machine, the appropriate configuration designator is indicated. Any artwork is
also specific.

NOTE: This manual services all configurations of the machine. Ignore references to options
not installed on the machine.

Warnings, Cautions and Notes

WARNING

A warning is used whenever an operating or maintenance procedure, practice, condi-
tion or statement, if not strictly observed, could result in personal injury.

A translated version of all warnings is in

Translation of Warnings

.

CAUTION

A caution is used whenever an operation or maintenance procedure, practice, condition or
statement, if not strictly observed, could result in damage to the equipment.

NOTE: A note is used where it is essential to highlight a procedure, practice, condition or state-

ment.

«
...
6
7
8
9
10
...
»

Summary of Contents for Phaser 3020





















































































































Reviews:

No comments