Xerox 490ST - Document Centre B/W Laser Printer System Administration Manual Download Page 298

Page: 298 / 322

Page 21 - 10

Xerox Document Centre System Administration Guide

LDAP Directory Setup (Internal Address Book)

The Document Centre 490/480/470/460 ST allows you to use the
Internal Company Address book, much the same as E-mail at your
workstation.

NOTE

Accessing LDAP Directory and Public Address Book are optional.

NOTE

Configuration of the LDAP directory settings requires the network
to support LDAP services.

The following steps assume you have not left the Properties tab,
Services and Internet Messaging.

Select LDAP Directory.

Summary of Contents for 490ST - Document Centre B/W Laser Printer



































































































































































































































































































































Search results

Summary of Contents for 490ST - Document Centre B/W Laser Printer

Reviews:

Related manuals for 490ST - Document Centre B/W Laser Printer

Brands by name

Popular brands

Xerox 490ST - Document Centre B/W Laser Printer, System Administration Manual

Search results

Summary of Contents for 490ST - Document Centre B/W Laser Printer

Reviews:

Related manuals for 490ST - Document Centre B/W Laser Printer

Brands by name

Popular brands