Xerox 1235DT - Phaser Color Solid Ink Printer Service Manual Download Page 37

Page: 37 / 239

Phaser 1235 Network Color Printer

E14

Front Cover B Open Close Front Cover B

E14-Front Cover B Open

Close the cover.

Inspect the switch and ensure the switch’s actuator is not broken.

Test the front cover open switch using the sensor test described in “Switch
scan test” on page 63.

Inspect the switch’s wiring harness.

Replace the engine controller board.

Black Drum Missing Reseat Drum, Power
Off/On

EA-Black Drum Missing

Cyan Drum Missing Reseat Drum, Power
Off/On

EB-Cyan Drum Missing

Magenta Drum Missing Reseat Drum, Power
Off/On

EC-Magenta Drum Missing

Yellow Drum Missing Reseat Drum, Power
Off/On

ED-Yellow Drum Missing

Remove and install the drum unit.

Inspect the spring-loaded drum contact assembly. Ensure they are clean
and move up and down freely. Remove the assembly and reseat it, if
necessary.

Replace the engine controller board.

Replace the printer unit chassis

Transfer Belt Missing Reseat Belt, Power
Off/On

EE-Transfer Belt Unit
Missing

Remove and re-install the transfer belt unit.

Clean the transfer belt unit’s contact on the front-left side of the engine
chassis. Clean the corresponding contacts on the transfer belt unit.

Install a new transfer belt unit.

Replace the engine controller board.

Replace the printer unit chassis.

Fuser Missing Reseat Fuser, Power Off/On

EF-Fuser Unit Missing

Remove and reinstall the fuser.

install a new fuser.

Replace the low-voltage power supply.

Replace the engine controller board.

Printer fault messages

Code

Front panel message

Service message

Summary of Contents for 1235DT - Phaser Color Solid Ink Printer
















































































































































































































































Search results

Summary of Contents for 1235DT - Phaser Color Solid Ink Printer

Reviews:

Related manuals for 1235DT - Phaser Color Solid Ink Printer

Brands by name

Popular brands

Xerox 1235DT - Phaser Color Solid Ink Printer, Service Manual

Search results

Summary of Contents for 1235DT - Phaser Color Solid Ink Printer

Reviews:

Related manuals for 1235DT - Phaser Color Solid Ink Printer

Brands by name

Popular brands