Xantrex Xantrex PRO XM 1000 Owner'S Manual Download Page 32

Page: 32 / 77

Installing the XM Series Inverter

975-0263-01-01

3–13

Chassis Ground Stud

Xantrex recommends that you attach the grounding cable to the chassis
ground stud with a ring terminal. This procedure will ensure that the wire
does not slip off the chassis ground stud.

To connect the cable to the chassis ground stud:

1. Remove the ground stud nut and star washer.

2. Strip 1/2 inch (13 mm) to 3/4 inch (19 mm) of insulation from the end

of the cable.

3. Attach the ring connector that will join the cable to the chassis ground

stud. The connector you use must create a permanent, low-resistance
connection. (See “Materials” on page 3–10.)

4. Fit the ring connector and star washer over the stud. The ring

connector should be flat against the XM Series Inverter chassis.

5. Tighten the ground stud nut.

Figure 3-4

Connecting the Grounding Cable

Star washer

Ground stud nut

Ring connector

Summary of Contents for Xantrex PRO XM 1000














































































Search results

Summary of Contents for Xantrex PRO XM 1000

Reviews:

Related manuals for Xantrex PRO XM 1000

Brands by name

Popular brands

Xantrex Xantrex PRO XM 1000, Owner'S Manual

Search results

Summary of Contents for Xantrex PRO XM 1000

Reviews:

Related manuals for Xantrex PRO XM 1000

Brands by name

Popular brands