background image

Viewing the Advanced Menu

975-0082-01-01

4–5

Viewing the Advanced Menu

The System Control Panel can display the Auto Gen Start menu in two 
formats: basic and advanced.

The Auto Gen Start basic menu is displayed by default. It lists status 
information and settings you may have to adjust routinely. See “The Auto 
Gen Start basic menu” on page 3–7 for a list of basic menu items and 
configuration information.

The Auto Gen Start advanced menu lists additional settings and sub-
menus. See “Auto Gen Start advanced menu” on page 3–18 for a list of 
advanced menu items and configuration information.

To view the Auto Gen Start advanced menu, you must go to the System 
Settings menu.

To view the Auto Gen Start advanced menu:

1. On the Select Device menu, use the down arrow button to highlight 

System (see Figure 4-1).

2. Press Enter.

The System Settings menu appears.

3. On the System Settings menu, use the down arrow button to highlight 

Global Menus and press Enter.

4. Use the up or down arrow button to select Advanced.

5. Press Enter.

This procedure causes advanced menus to be displayed for all devices on 
the Xanbus system. You can return to displaying the basic menu for the 
Auto Gen Start by selecting Basic Menu on the Auto Gen Start menu.

Figure 4-1

Selecting the System menu

Summary of Contents for Automatic Generator





























































































































Reviews: