background image

28 

 

How To Remove and Insert Pins In Connectors 

Look down inside the connector; you will see a metal pin. The pin is held in place by a 

small tab that bends outward. Reach inside the front of the connector with a dental pick or 

jeweler

’s screwdriver and bend the tab in then pull the metal pin out the back of the 

connector. Reinsert the new wires into the white connectors. 

***Also see instructions on Page 36 with photos. 

 

How To Replace Headlight Bulb 

To replace the headlight you will need to split the dash. To do this you will need to remove 

the 4 screws that hold the dash together. Next, with a pinching motion on the top of the 

dash on both sides on the clear lens, you will separate the dash. Inside there is a small tab, 

that is why the pinching must be done. When the dash is separated, you will then see the 

headlight assembly. Simply remove the 2 screws on the headlight housing and swap that 

one out for the new one. Now put the screws back in, re-assemble the dash, and you 

should be ready to go. 

 

 

How To Repair A Flat Tire 

 

1) To remove either tire place the scooter on top of a solid object that holds the wheels off 

of the ground. 

2) For the front remove the bolt from one side of the axle by using two 14mm wrenches. 

Pull the axle out from the side. Replace in reverse order 

3) For the back tire with the scooter sitting off of the ground remove one of the nuts on the 

axle using two 14mm wrenches.   

a) Loosen the chain tensioners so that there is some slack in the chain.   

b) Pull axle out to one side while holding wheel. 

c) Move wheel towards the front and remove chain from sprocket. 

d) Assemble in reverse direction being sure to adjust chain tensioner properly. See 

manual for further directions. 

4) Remove tire from wheel in the same manner as you would on a bicycle by letting the air 

out of the valve and using tire irons or screw drivers to open one side. Remove old inner 

tube, confirm there are no objects inside and replace with new inner tube. Inflate tire to 

about 40 lbs pressure and re-install. 

 

 

 

 

 

 

Summary of Contents for X-370













































Reviews: