background image

M A   3     S P E C T R O P H O T O M E T E R  

4

 

Proprietary Notice 

The information contained in this manual is copyrighted information proprietary to X-Rite, Incorporated.  
Publication of this information does not imply any rights to reproduce or use it for purposes other than installing, 

operating, or maintaining this instrument described herein. No part of this manual may be reproduced, 

transcribed or translated into any language or computer language in any form or by any means: electronic, 

magnetic, mechanical, optical, manual, or otherwise; without the prior written permission of an authorized officer 

of X-Rite, Incorporated. 
Patents: www.xrite.com/ip 
“© 2017, X-Rite, Incorporated. All rights reserved” 

X-Rite® is a registered trademark of X-Rite, Incorporated. All other logos, brand names, and product names mentioned are the properties of their respective 

holders. 

Warranty Information 

X-Rite warrants this Product against defects in material and workmanship for a period of twelve (12) months 

from the date of shipment from X-Rite’s facility, unless mandatory law provides for longer periods. During such 

time, X-Rite will either replace or repair at its discretion defective parts free of charge.   

 

X-Rite’s warranties herein do not cover failure of warranted goods resulting from:  (i) damage after shipment, 

accident, abuse, misuse, neglect, alteration or any other use not in accordance with X-Rite’s recommendations, 

accompanying documentation, published specifications, and standard industry practice; (ii) using the device in 

an operating environment outside the recommended specifications or failure to follow the maintenance 

procedures in X-Rite’s accompanying documentation or published specifications; (iii) repair or service by anyone 

other than X-Rite or its authorized representatives; (iv) the failure of the warranted goods caused by use of any 

parts or consumables not manufactured, distributed, or approved by X-Rite; (v) any attachments or 

modifications to the warranted goods that are not manufactured, distributed or approved by X-Rite. Consumable 

parts and Product cleaning are also not covered by the warranty. 

 

X-Rite‘s sole and exclusive obligation for breach of the above warranties shall be the repair or replacement of 

any part, without charge, which within the warranty period is proven to X-Rite‘s reasonable satisfaction to have 

been defective. Repairs or replacement by X-Rite shall not revive an otherwise expired warranty, nor shall the 

same extend the duration of a warranty.  

 

Customer shall be responsible for packaging and shipping the defective product to the service center 

designated by X-Rite. X-Rite shall pay for the return of the product to Customer if the shipment is to a location 

within the region in which the X-Rite service center is located. Customer shall be responsible for paying all 

shipping charges, duties, taxes, and any other charges for products returned to any other locations. Proof of 

purchase in the form of a bill of sale or receipted invoice which is evidence that the unit is within the Warranty 

period must be presented to obtain warranty service. Do not try to dismantle the Product. Unauthorized 

dismantling of the equipment will void all warranty claims. Contact the X-Rite Support or the nearest X-Rite 

Service Center, if you believe that the unit does not work anymore or does not work correctly.   

 

THESE WARRANTIES ARE GIVEN SOLELY TO BUYER AND ARE IN LIEU OF ALL OTHER WARRANTIES, 

EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF 

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR APPLICATION, AND NON-

INFRINGEMENT. NO EMPLOYEE OR AGENT OF X-RITE, OTHER THAN AN OFFICER OF X-RITE, IS 

AUTHORIZED TO MAKE ANY WARRANTY IN ADDITION TO THE FOREGOING. 

 

IN NO EVENT WILL X-RITE BE LIABLE FOR ANY OF BUYER’S MANUFACTURING COSTS, OVERHEAD, 

LOST PROFITS, GOODWILL, OTHER EXPENSES OR ANY INDIRECT, SPECIAL, INCIDENTAL OR 

CONSEQUENTIAL DAMAGES BASED UPON BREACH OF ANY WARRANTY, BREACH OF CONTRACT, 

NEGLIGENCE, STRICT TORT, OR ANY OTHER LEGAL THEORY. IN ANY EVENT OF LIABILITY, X-RITE’S 

MAXIMUM LIABILITY HEREUNDER WILL NOT EXCEED THE PRICE OF THE GOODS OR SERVICES 

FURNISHED BY X-RITE GIVING RISE TO THE CLAIM. 

Summary of Contents for MA 3
























Reviews: