background image

 

45  

and press GO switch to quit. 

e. 

When “End track” is displayed on the LCD, press 
GO switch to quit directly since the number shown 
is already 2. 

f. 

Press MODE switch to number 5 at “Begin track” 
and press GO to quit.   

g. 

When “End track” is displayed on the LCD, press 
GO switch to quit directly since the track number 
shown is already 5. 

h. 

Press MODE to number 7 at “Begin track” and quit. 

i. 

Press MODE switch to number 13 at “End track” 
and quit. 

j. 

Press GO switch directly to following “Begin track” 
and End track” selection to finish the track 
selection on No. 1 master disc. 

k. 

The next function will be Finalize setting. Since 
there is still another master to be selected from, 
leave the option as No and press Go to quit. 

l. 

Duplicator will start to copy those tracks you 
selected just now onto blank target discs in writers. 

m. 

After copy is finished, duplicator will eject master 
and show “Pass” on LCD but those un-finalized 
discs will still be remained in writers for further 
operation. 

n. 

Load No.2 master in ROM drive and continue to 
select from second master. 

o. 

Repeat steps (d) to (k) above but change the 
Finalize setting to Yes in (k) and the duplication for 
tracks selected will then begin. 

p. 

When copy is finished, the passed discs will be 
ejected from writers directly. 

q. 

If total capacity of selected tracks exceed the max. 
capacity on the detected blank discs, the 
duplicator will refuse to accept additional track 
selection. 

Summary of Contents for CD-398



























































Reviews: