manualshive.com logo in svg

Woodway ST PPS 43 Med, User Manual

Share
Download
Woodway ST PPS 43 Med User Manual Download Page 53

 

 

 

47 | UM-PP-EN-03 

6.5.4

 

Remove Handrails  

Side Panels 

Loosen the screws on both side panels (3 per side) with a Phillips screwdriver.  
On PPS Bari-Mill models, the cutout for the railing is covered with an additional panel. Loosen the 
fixing screws on the panels (2 per side). See the following figure for the placement of side panel fixing 
screws and note that there are fixing screws on both sides of the device. 

 

Fig. 22 Side panel fixing screws 

1.

 

PPS Bari-Mill side panel fixing screws 

2.

 

PPS Med / Ortho side panel fixing screws 

Electronics Covering 

The drive and control electronics are located on the right side of the device as seen from walking 
direction.  
To remove the metal cover (shield) loosen the 4 fixing screws. 

 

Fig. 23 Remove electronics shielding panel 

 

 

1 

2 

Summary of Contents for ST PPS 43 Med



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands