C A U T I O N
C A U T I O N
Check the CAMERA ID, PROTOCOL and BAUDRATE
settings prior to testing. A PTZ camera cannot be
controlled unless all three settings are correct.
1. Make sure to check the communication protocol, transmission speed, and PTZ ID.
2. The input signal from the controller can be checked when the communication line is connected to the
Rx terminal of the Rapport III.
SET
Control Setup of PTZ
PTZ ADDR : Setup the PTZ ID. The default value
is 001. To change the PTZ ID use the & keys.
keys and it moves by +1, -1 steps.
The available values are 001 through to 255.
The PTZ ADDR menu bar is accessed, on the top section of the LCD screen,
when the key is depressed for more than 3 seconds.
The activated menu can be changed to PROTOCOL and BAUDRATE
by pressing the & keys.
PROTOCOL : Used to set the PTZ PROTOCOL .
The default value is set to PELCO-D. To change
to another protocol, use the & keys to see
the available protocols.
BAUDRATE : Sets the TRANSMISSION SPEED.
The default value is 2.4Kbps.
Use the & keys to alter the speed – the
available options are from 2.4Kbps~ 115.2Kbps.
UTP CABLE TESTER
SET
SET
Once the connection is complete, the connectivity of the cable under test
is checked by pressing the key. Straight through and crossed
cables can be verified.
Disconnections and short-circuits are also displayed.
Connect the UTP cable to be tested to the UTP port of the Rapport III,
and connect the other end of the cable to the yellow UTP test dongle.
FUNCTIONAL SPECIFICATION
FUNCTIONAL SPECIFICATION
Short-circuit & Disconnection
Straight cable
Cross cable
C
PTZ
LOSS
MODE
OK
PTZ ADDR :001
PROTOCOL : (01)PELCO-D
BAUDRATE:19.2Kbps
PARITY : NONE
SPD
15
GPST
001
SPST
001
FUNC
01
MENU
C
PTZ
LOSS
MODE
OK
PTZ ADDR :001
PROTOCOL : (01)PELCO-D
BAUDRATE:19.2Kbps
PARITY : NONE
SPD
15
GPST
001
SPST
001
FUNC
01
MENU
C
PTZ
LOSS
MODE
OK
PTZ ADDR :001
PROTOCOL : (01)PELCO-D
BAUDRATE:19.2Kbps
PARITY : NONE
SPD
15
GPST
001
SPST
001
FUNC
01
MENU
CABLE
LOSS
MODE
TEST
NO CONNECTION
CABLE
LOSS
MODE
TEST
NO CONNECTION
(1) XXXXX (X)
(2) XXXXX (x)
(3) XXXXX (X)
(4) XXXXX (X)
(5) XXXXX (X)
(6) XXXXX (x)
(7) XXXXX (X)
(8) XXXXX (X)
CABLE
LOSS
MODE
TEST
STRAIGHT
(1) (1)
(2) (2)
(3) (3)
(4) (4)
(5) (5)
(6) (6)
(7) (7)
(8) (8)
CABLE
LOSS
MODE
TEST
CROSS
(1) (3)
(2) (5)
(3) (7)
(4) (1)
(5) (2)
(6) (4)
(7) (6)
(8) (8)
MODE
TEST
Change the mode
Check the cable type by pressing
button.
C
PTZ
LOSS
MODE
OK
PTZ ADDR :001
PROTOCOL : (01)PELCO-D
BAUDRATE:19.2Kbps
PARITY : NONE
SPD
15
GPST
001
SPST
001
FUNC
01
MENU
PARITY: Set the parity to NONE, ODD and EVEN
by using & keys.
40
MULTI FUNCTIONAL CCTV TESTER
41
MULTI FUNCTIONAL CCTV TESTER
