Wolf 4380000 Service Manual Download Page 8 | Manualshive

Page: 8 / 20

Wolf 4380000 Service Manual Download Page 8

Page 8

6-38

7040317 - Revision A - September, 2015

Component Removal

Built-In (BI) Series

Built-In (BI) Series

(SWS #4380000)

(SWS #4380000)

Model BI-36F Interior Cosmetic / Mechanical Components

Door Gasket

A dart at the back of the door gasket fits into metal
channels attached to the inside perimeter of the door.

To remove a door gasket, starting at one corner, pull
the gasket dart from the metal channels. (See Figure
6-93).

Adjustable Door Shelves

Removal and adjustment of the door shelves is
achieved by sliding the grooves in the shelving end-
caps over the molded retaining ribs of the door liner.

Lift out and up to remove, push in and down to install.
(See Figure 6-94).

Cantilever Shelf Assembly

To adjust and/or remove a freezer cantilever wire shelf
assembly (See Figure 6-95):

1.

Lift front of shelf up slightly.

2.

Lift back of shelf up to disengage the shelf ladder
hooks from the shelf ladders.

3.

Pull shelf forward and out of the shelf ladders.

Figure 6-93. Door Gasket Removal

Metal Channels

Gasket

Figure 6-94. Adjustable Door Shelf

Door Shelf

2

1

3

Figure 6-95. Cantilever Shelf Removal

«
...
6
7
8
9
10
...
»

Summary of Contents for 4380000





















Reviews:

No comments