manualshive.com logo in svg

Wolf 4380000, Service Manual, Page: 13 / 20

Share
Download
Wolf 4380000 Service Manual Download Page 13

Page 13

6-43

7040317 - Revision A - September, 2015

Built-In (BI) Series

Built-In (BI) Series

(SWS #4380000)

(SWS #4380000)

Component Removal

Lower LED Light Tube

The LED light tube is held by plastic light clips that are
inserted into the lower duct.  The light tube wire leads
are inserted back through a plastic grommet in the
lower duct.

To remove the LED light tube, first remove all cantilever
shelves, the fixed glass shelf, all freezer baskets, ice-
maker assembly, upper light diffuser, light diffuser
brackets, upper duct assembly and middle duct assem-
bly and lower duct assembly, then (See Figure 6-108):

1.

Extract plastic grommet around light tube wire leads
from hole in lower duct.

2.

Pass light tube wires through slot in side flange of
lower duct.

3.

Pull light tube from plastic light clips.

Evaporator Fan Motor

The freezer evaporator fan motor sits on top of the
evaporator fan shroud bracing with its shaft passing
through a hole in the brace; the motor is then held in
place by a fan bracket snapping together with the brac-
ing over the back side of the motor.

To remove the evaporator fan motor, first remove all
cantilever shelves, the fixed glass shelf, all freezer bas-
kets, icemaker assembly, upper light diffuser, light dif-
fuser brackets, upper duct assembly, middle duct
assembly and lower duct assembly, then (See Figure 6-
109):

1.

Pull fan blade from fan motor shaft.

2.

Using a flat-bladed screwdriver, pry fan bracket
clips off of the tabs at each side of shroud bracing.

3.

Lift fan motor off of fan shroud.

Evaporator Defrost Heater

The evaporator defrost heater is held in place at the
bottom of the evaporator with defrost heater clips.

To remove the defrost heater, first remove all cantilever
shelves, the fixed glass shelf, all freezer baskets, ice-
maker assembly, upper light diffuser, light diffuser
brackets, upper duct assembly, middle duct assembly
and lower duct assembly, then (See Figure 6-110):

1.

Disconnect heater electrical leads.

2.

Using a small needle-nose pliers, detach heater
clips by pulling end tab of clips away from evapora-
tor, then remove heater from compartment.

Figure 6-109.  Evaporator Fan Removal

Bracket
Clip

Figure 6-110.  Defrost Heater Removal

Screwdriver

Fan

Motor

Heater

Heater Clips

Figure 6-108.  Lower LED Light Tube Removal

Lower Duct 

Assembly

LED Light Tube

Grommet

Slot in

Lower

Duct

Summary of Contents for 4380000





















Reviews:

No comments