manualshive.com logo in svg

Wolf 4380000, Service Manual, Page: 7 / 20

Share
Download
Wolf 4380000 Service Manual Download Page 7

Page 7

6-37

7040317 - Revision A - September, 2015

Built-In (BI) Series

Built-In (BI) Series

(SWS #4380000)

(SWS #4380000)

Component Removal

Door Assembly

The door assembly is secured to the top and bottom
door hinges with screws.  The post of the bottom door
hinge fits down into a bearing in the bottom cabinet
hinge assembly’s door adjuster.

To remove a door assembly, the top hinge assembly
must be removed first.  Then, with one hand at each
side of the door, open the door forty-five to ninety
degrees and lift it off of the bottom cabinet hinge
assembly.  (See Figure 6-91)

Bottom Cabinet Hinge Assembly

The bottom cabinet hinge assembly is attached to the
bottom of the unit with bolts.

To remove the bottom cabinet hinge assembly, first
remove the top hinge assembly and the door.  Then,
using a 1/2” wrench or socket, extract the cabinet hinge
mounting bolts and pull the hinge assembly from the
unit.  (See Figure 6-92)

Figure 6-91.  Door Assembly Removal

Door Assembly

Figure 6-92.  Cabinet Hinge Assembly Removal

Bottom Cabinet
Hinge Assembly

Bottom Cabinet
Hinge Assembly

Bolts

Summary of Contents for 4380000





















Reviews:

No comments