Wolf 4380000 Service Manual Download Page 11

Page 11

6-41

7040317 - Revision A - September, 2015

Built-In (BI) Series

Built-In (BI) Series

(SWS #4380000)

(SWS #4380000)

Component Removal

Figure 6-102.  Upper Light Assembly

Light Bulb

Light Bulb

Ground Clip

Light Bracket Assembly

Figure 6-103.  User Interface Module Removal

(viewed from behind)

UIM (Rear View)

Lower Tab

Slot in Display Support

Upper LED Light Bulb and Light Bracket Assembly

The lighting assemblies are located behind the light dif-
fuser at the top of the compartment.

To remove LED light bulbs, first remove the light dif-
fuser, then turn the bulb counterclockwise to remove it.
(See Figure 6-102)

Light bracket assemblies are secured with screws to
the compartment ceiling.

To remove a light bracket assembly, first remove the
light diffuser and LED light bulbs, then (See Figure 6-
102):

1.

Extract bracket mounting screws.

2.

Lower assembly down and disconnect the lighting
wire harness.

3.

pull ground clip from side of bracket.

User Interface Module (UIM - Control Panel Assy)

The user interface module (UIM) is located at the top
front of the freezer compartment and is secured with
tabs at each end fitting into slots in the display support.  

To remove the user interface module, first remove the
upper light diffuser, then (See Figure 6-103):

1.

At each end of user interface module, reach behind
the control panel and push the lower tabs upward
while pulling the bottom edge away from the display
support.

2.

Once the lower tabs are disengaged, lower the
assembly down and disconnect the electrical lead
from the user interface module PC board.

Upper Duct Assembly

The upper duct assembly has notches at the bottom of
each side flange that fit over locating pins on the shelf
ladders; screws at the top of the duct secure it to the
back wall of the compartment.

To remove the upper duct assembly, first remove all
cantilever shelves, fixed glass shelf, upper light diffuser
assembly and light diffuser brackets, then (See Figure
6-104):

1.  Extract top mounting screws.
2.  Pull top of duct forward and pull grounding wire clip

from top edge of upper duct, then lift the duct up off
of shelf ladder pins.

Figure 6-104. Upper Duct Assembly Removal

Screws

Upper Duct
Assembly

Summary of Contents for 4380000





















Reviews: