manualshive.com logo in svg

WM Systems BE0077F, User Manual

Share
Download
WM Systems BE0077F User Manual Download Page 70

 

 

 

5.

 

Then  the  next  message  appears  on  the  screen  in  the  browser.  Then  the  refresh 

method has started, while the 

LED3

 is continuously lighting by 

red 

and sometimes 

the 

LED2

 is flashing.  

 

 

6.

 

At the end of the installation - the LEDs will no longer flash - the system will reboot 
2x, then the 

OpenWrt

®

 system will start and load as described. 

 

Important

! The update window does not close and does not detect the availability 

of the OpenWrt website. Therefore, close the upgrade browser window at the end of 

the installation. 

 

7.

 

When 

LED3

  or 

LED2

  is  available  again  and  stays  green,  re-enter  the  home  page 

address in Mozilla Firefox to access the local OpenWrt interface. 

 

8.

 

Check the updated software versions on the home page for statuses. 

 

 

6.2

 

Installing applications 

Open the 

System

 / 

Software

 menu. 

Summary of Contents for BE0077F

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands