background image

Anchor 4000 

Installer manual  

Installation and commissioning instructions  

en_A4000-Teil 2-Errichterhandbuch V2.03.docx 

1 / 7 

 

 

Note: 

On the cover sheet you can find warning information, and an explanation of the symbols and 

terms used, together with the exclusion of liability. 

 

 

 

 

 

 

 

Contents 

General ................................................................................................................................. 2

 

Preparation for installation ..................................................................................................... 3

 

Installation dimensions ...................................................................................................... 3

 

Preparation of the boltwork / door ...................................................................................... 3

 

Installation ............................................................................................................................. 4

 

Wiring / installation ................................................................................................................ 5

 

Connection of an analog keypad ....................................................................................... 5

 

Connection P- signal plus / UART ..................................................................................... 6

 

Function test .......................................................................................................................... 6

 

Input of the opening code .................................................................................................. 6

 

Keypad test ....................................................................................................................... 7

 

System setup ........................................................................................................................ 7

 

 

 

 

 

 

Mount the keypad before installing the electronic lock. All the keypads of the Primor series 

can  be  used.  Details  on  installing  the  keypads  are  given  in  the  "Primor  installation 

instructions (see sections 3 to 7)". 

 

Summary of Contents for Anchor 4000 Series








Reviews: