background image

1

INTRODUCTION

Congratulations on your purchase of the 

Gas Tracker

 data collection system. Each 

Gas Tracker

 

unit is proudly made in the USA and quality tested and inspected prior to shipping. Please check 

the box upon receiving the products for any damage that may have occurred during transit and 

to ensure all components are accounted for. 

Gas Tracker

 offers the capability to monitor the gas flow rate as a portable unit or as an inline system. 

The unit has a built-in battery for easy transport without the need of nearby electrical outlets. 
This guide is designed to assist the user whose primary responsibility is to operate and maintain 

the 

Gas Tracker

 system. This manual provides specific information on the installation, safety, 

basic operation, and maintenance. 

Please read, understand and follow all safety precautions 

noted in this manual. 

For customer service and support, contact ELCo Enterprises at 517.782.8040 or toll free 1.866.584.7281. 

This manual and additional product information is available on our website at 

wire-wizard.com

.

WARRANTY

ELCo Enterprises, Inc. (hereinafter “ELCo”) shall warrant this product to be free of defects in material 

and/or workmanship for a period of one (1) year from the date of shipment to the buyer. The 

warranty shall cover 100% of all parts and labor with the exception of misuse, abuse, neglect and 

typical consumables as determined by ELCo. Failure to follow proper installation and/or maintenance 

procedures specified in the operating instructions will void this warranty. ELCo will, at its option, 

repair, replace or issue a credit for the value of the defective product within the warranty period.
Buyer accepts all responsibility for compliance with any/all Local, State and Federal Laws or 

Regulations including Regulations of Foreign Governments.
No equipment shall be returned without a Return Authorization Number. Upon evaluation and validation 

of warranty, replacements or repairs will be sent to the Buyer. If a replacement is needed immediately, a 

purchase order is required to cover the cost of the product until the warranty is determined.
ELCo’s warranty is limited to replacing any goods that are proved to be defective and ELCo in no 

event shall have any liability for paying incidental or consequential damages including and without 

limitation, damages resulting in personal or bodily injury or death, or damages to, or loss of use of any 

property. Notwithstanding any of these terms and conditions, the warranties set forth shall apply in 

connection with any sales of goods, services or design by ELCo and are in lieu of all other warranties, 

express or implied, including warranties of merchantability and fitness for a particular purpose.

PRODUCT REGISTRATION

Please register this product online or by phone within 14 days after receipt to 

validate warranty.
Register this product online by going to 

wire-wizard.com/register

 or scanning 

the QR code on the right, or you may call 517.782.8040 to register by phone. Registering this 

product will allow us to provide firmware and software updates via email, as well as expedited 

service should there be any problems potentially covered by this warranty in the future. 
Please record the following information for this product and retain for your records:
Model #: ___________________   Lot #: _________________   Shipment Date: _______________

LIMITED ONE (1) YEAR WARRANTY 

REGISTRATION REQUIRED: VISIT WIRE-WIZARD.COM/REGISTER

Summary of Contents for GAS TRACKER

























Reviews: