background image

10

GAS TRACKER INSTALLATION & OPERATION MANUAL

Changing Alert Settings

 

▶ Alert settings are changed by going to the 

Setup

 tab and then clicking 

Alerts

.

 

▶ Each alert must be clicked individually and changed to the desired value.

 

▶ Begin by clicking the desired alert (example: 

Low Flow

). 

 

▶ In the keypad area press the double arrow to delete the preexisting value.

 

▶ Type in the desired value on the keypad.

 

▶ Press 

OK

.

 

▶ If an alert is to be disabled do so with the 

Disable

 button to the left of the keypad. 

Changing Outputs

 

▶ Output settings are changed by clicking the 

Setup

 tab and then clicking the 

Output

 button. 

 

▶ Each output can be modified by clicking the button under the output number.

 

▶ When selected, the new output replaces the one that was previously configured.

 

▶ Use the back button to go back to the 

Setup

 page.

 

▶ Configuring signals via the 

Output

 information can be found in 

Appendix B 

of the manual. 

Updating the Unit’s Time

 

▶ Each 

Gas Tracker

 has multiple time zones that can be selected. 

 

▶ If the Timezone needs changed, click the 

Setup

 tab. 

 

▶ Press the

 Timezone

 button in the upper right hand corner. 

 

▶ Select the appropriate time zone. 

 

▶ If the time is out of sync for any reason the 

Gas Tracker

 must be connected to a PC. Do this  

 

by following the instructions in the 

Software Use

 section of the manual under Information. 

Changing Units

 

▶ If the units need changed from 

Metric

 to 

Imperial

 or vice versa do so on the 

Setup

 page. 

 

▶ After clicking the 

Setup

 tab, click the button under the text 

Units

. The text that shows in  

 

the box (ie. 

Imperial

) are the units that are selected.

Summary of Contents for GAS TRACKER

























Reviews: