background image

 

 

 

Using the SFI Menus 

 

ProCam 1500 SFI Manual 

13 

Ch 3 

1095900

 

PRESS RESET WHEN DONE

FEED LENGTH

ACCELERATION

MAX RUN SPEED

2.252000
40.00000
4000.000

INCHES
%
INCHES/MIN

 

Figure 3-6.  Check setup display 

 

 
 
 

"Check setup" is a diagnostic tool available in SFI which lets you view the feed 
parameters in your servo feed.  It gives you an opportunity to make sure that these 
parameters match your currently loaded setup.   
 
 
Notice that you cannot change any of these items.  This display is for viewing purposes 
only. 
 
 
When you are done looking at the information on the screen, press the RESET key to 
return to the Feed Initialize menu, and then one more time to go back to the main 
Initialization menu. 

Security access 

You use this choice on the Initialization menu to lock out "Adjust feed" so that 
unauthorized personnel cannot perform adjust feed settings in Run mode. 

Locking Adjust feed   

To prevent unauthorized personnel from unlocking "adjust feed", you must remove the 
Program/Run key once ProCam is switched to Run mode. This will prevent unauthorized 
access into the Initialization or Program modes, so that feed settings cannot be unlocked 
or altered. The key has to be positioned at "PROGRAM" to get into these modes. 

 

Select "Security access" from the Initialization menu. Select "Program and Run modes" 
shown to the right of the action "Adjust feed", as illustrated in Figure 3-7.  The default 
settings (settings made at the factory) allow this action to be made in Program and Run 
modes.  

Summary of Contents for ProCam SFI





























Reviews: