background image

22

21

7.0 TROUBLESHOOTING

Problem: Chlorine taste and/or odor in the filtered water.

Cause:

The level of chlorine in your water supply exceeds maximum limits, and has

destroyed the Ultra Filtration membrane.

Correction:

If the water supply contains more than 2.0 ppm of chlorine, additional

filtering of the water supply to the UF is needed. Correct this condition before doing
maintenance on the Ultra Filtration system.

Cause:

The pre filter is no longer reducing chlorine from the water supply.

Correction:

Replace the pre filter, post filter and Ultra Filtration membrane cartridges. 

Problem: No water or decreased water flow.

Cause:

Pre-Filter A is clogged.

Correction:

Replace Pre-Filter A.

Cause:

Flow through the microbiological purifying filter will decrease and eventually clog

when exposed to an excess of microbiological loading materials in the water.
This failsafe feature reduces the chance of product use beyond its intended life, and will
shut down the filter when it is exposed to contaminated water.

Correction:

Replace all filter cartridges.

Problem: Taste and/or Odor.

Cause:

Filter cartridges exhausted.

Correction:

Replace all filter cartridges.

Cause:

System contaminated.

Correction:

Sanitize system. Call location of purchase for instructions.

Problem: FCSPU1 LED indicator light does not function after battery change.

Cause:

Battery dead.

Correction:

Replace with new battery.

Cause:

Battery installed incorrectly.

Correction:

Install battery correctly.

Problem: Water leaks at push connect fittings.

Cause:

Tubing not pushed in all the way. 

Correction:

Push tubing in all the way into fittings.

Cause:

Tubing not cut square.

Correction:

Cut tubing square.

Cause:

Tubing nicked.

Correction:

Remove nicked portion, reinsert tubing into fitting.

Cause:

Outer tubing surface not smooth. 

Correction:

Remove rough portion, reinsert tubing into fitting.

Problem: Tubing does not connect to water filtration system.

Cause:

Black plugs are still connected to the unit.

Correction:

Remove black plugs and insert tubing into fitting.

Summary of Contents for Finecel FCSPU1













Reviews: