Windhager DuoWIN Assembly Instructions Manual Download Page 52 | Manualshive

Page: 52 / 76

background image

52

2.

For the Installer

2.4.36 Pellet boiler: Laying the LON cable

The LON cable is the cable connecting the two boilers. It goes from the LON connection board of the pellet boiler
to the control panel of the wood gasification boiler.

– Lay the LON cable from the LON connection board of the pellet boiler along the cable duct and through the

opening in the side panel to the control panel of the wood gasification boiler. If there is no opening, a hole has
to be drilled with a Ø 16 mm in accordance with the sketch.

– Push the grommet (on LON cable) into the opening in the side panel of the wood gasification boiler.

– Connect the LON plug to the control panel of the wood gasification boiler.

Fig. 124 Laying the LON cable

LON cable grommet

Orange Brown Red

Cable duct

LON cable

Wood gasification boiler control panel

LON connection board for pellet boiler

140 mm

90 mm

Ø 16 mm

Drill hole for grommet if no opening is availabl

e!

LON plug

12 V

«
...
50
51
52
53
54
...
»

Summary of Contents for DuoWIN













































































Reviews:

No comments

Related manuals for DuoWIN

aroSTOR VWL B 270/5

Brand: Vaillant Pages: 172

Brand: Laars Pages: 4

Brand: Radijator Pages: 70

Brand: MIKOTERM Pages: 38

Brand: MONTAGUE Pages: 36

ECO HEAT 10 CA II PLUS

Brand: Gorenje Pages: 74

Brand: Ideal Boilers Pages: 4

Brand: Daikin Pages: 416

DynaFlame Series

Brand: Camus Hydronics Pages: 92

Brand: Unical Pages: 52

Brand: Unical Pages: 72

Brand: Unical Pages: 80

CompactGas 1000

Brand: Hoval Pages: 34

MEGAPREX N 1060

Brand: LAMBORGHINI Pages: 44

Vela X N 24 MB/IT

Brand: Lamborghini Caloreclima Pages: 82

ZB 7-28 R 28 HE

Brand: Benchmark Pages: 48

Brand: Aerco Pages: 122

Brand: Baxi Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands