manualshive.com logo in svg

Windhager DuoWIN, Assembly Instructions Manual, Page: 30 / 76

Share
Download
Windhager DuoWIN Assembly Instructions Manual Download Page 30

30

2. 

For the Installer

2.4.14  Wood gasification boiler: thermocontrol sensor installation

–  Bend the cut-out (feed-through) at the bottom of the side panel so it is not in the way. Route the thermocontrol 

sensor (green cable) down the front of the right side panel and through the feed thr

ough – Fig. 46, 47. 

–  Insert the sensor into the protective tube over the ash door in the front; hook the spring in place – Fig. 48, 49. 

Information!

Pull the protruding cable from the thermocontrol sensor back into the side panel or control panel. 
The cable must not hang out, so it does not become caught in the ash door.

–  Secure the thermocontrol sensor cable to the side panel with a cable tie – Fig. 49.

Fig. 46  Inserting the thermocontrol sensor 

at the top

Fig. 47  Threading through thermocontrol 

sensor

Fig. 48  Securing the thermocontrol sensor 

with spring

2.4.15  Wood gasification boiler: thermocontrol sensor cover installation

–  Attach the thermocontrol sensor with 4 self-tapping screws – Fig. 50.

Cut-out feed-
through 

Fig. 49  Pull  back  the  cable  and  secure  

with cable ties

Cable tie

Fig. 50  Attaching the cover over the thermocontrol sensor with 4 screws

2 each of

2 each of

Summary of Contents for DuoWIN













































































Reviews:

No comments