manualshive.com logo in svg

Windhager DuoWIN, Assembly Instructions Manual, Page: 14 / 76

Share
Download
Windhager DuoWIN Assembly Instructions Manual Download Page 14

14

2. 

For the Installer

2.4  Installation sequence

2.4.1  Minimum service clearances for fire protection, cleaning, and 

maintenance

It  is  essential  to  comply  with  the  following  minimum  service  clearances  from  flammable  materials  and  for 
connections, cleaning, and maintenance.

Attention!

Follow  the  installation  guidelines  for  boiler  rooms!  The  configuration  of  the  exhaust  line  must 
comply with technical fire protection requirements in accordance with the applicable regulations, 
standards, and guidelines.

Minimum clearances between the exhaust pipe incl. exhaust probe or boiler outlet (connecting piece to flue) 
and flammable parts

400

1

 mm

for an uninsulated exhaust pipe

100

1

 mm

for an insulated exhaust pipe (min. insulation thickness of 2 cm)

50

2

 mm

for approved, double-walled system flues

1

  DIN V 18 160-1

2

  in accordance with approval/identification of system flue

 

 1393 

 1

100 

 565 

 85 

 min. 550 

 min. 400

 2028 

 2065 

Fig. 6 

DuoWIN – top view

All dimensions in mm:
Minimum room heights: 1850 mm

Summary of Contents for DuoWIN













































































Reviews:

No comments