Windhager DuoWIN Assembly Instructions Manual Download Page 51

Page: 51 / 76

For the Installer

1 x

M5x12

Fig. 119 Screw the cladding front to the bot-

tom bracket

2.4.35 Pellet boiler: Mount the cover on the integral fuel hopper side

– Hook the cover on the integral fuel hopper side (Fig. 120) into the 2 rear bayonet locks – on the side panel of

the wood gasification boiler and secure each with self-tapping screws – Fig. 121, 122.

– Screw the inside of cover on the integral fuel hopper side to the cladding side using 2 self-tapping screws –

Fig. 123.

Fig. 120 Cover on integral fuel hopper side

Fig. 121 Hook the cover on the integral fuel

hopper side into the bayonet locks

and secure with 1 self-tapping screw

1 x

Fig. 122 At the back of the cover on the integral

fuel hopper side, screw into position with

1 self-tapping screw and assembly bracket

Fig. 123 Screw the cover on the integral

fuel hopper side to the inside of the

cladding side twice

1 x

2 x

Summary of Contents for DuoWIN













































































Search results

Summary of Contents for DuoWIN

Reviews:

Windhager DuoWIN, Assembly Instructions Manual, Page: 51 / 76

Search results

Summary of Contents for DuoWIN

Reviews: