manualshive.com logo in svg

Wincor Nixdorf CINEO C4080, Installation Manual

Share
Download
Wincor Nixdorf CINEO C4080 Installation Manual Download Page 187

Appendix

 

Compliance with

 standards and certifications 

01750223447 D 

CINEO C4080 - Installation Guide 

175

 

Compliance with standards and 
certifications 

Standards met 

Safety standards: 

IEC 60950, 
EN 60950,  
CSA C22.2-60950, 
UL 60950 

EMC standards: 

EN 55022 / B,  
EN 55024,  
FCC CFR 47, part 15, subpart B, class A, 
ICES-003 (CSA 108.8) 

 

Conformity 

The CE mark of conformity attached to the product or its package indicates 
that the product complies with the requirements of the following EC directives:   

  EMC Directive 2004/108/EC 
  Low Voltage Directive 2006/95/EC 
  RoHS Directive 2011/65/EC 

The corresponding statement of compliance has been issued by: 

WINCOR NIXDORF International GmbH 
Heinz-Nixdorf-Ring 1  

33106 Paderborn  

Germany 

Notes concerning radio interference suppression 
and electrical safety 

All other devices connected to this product must comply with the EMC 
Directive 89/336/EEC including amending directive 93/68/EEC (as of 

Summary of Contents for CINEO C4080



































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands