manualshive.com logo in svg

Wincor Nixdorf CINEO C4080, Installation Manual

Share
Download
Wincor Nixdorf CINEO C4080 Installation Manual Download Page 129

Installation 

Installation with window frame

 

01750223447 D 

CINEO C4080 - Installation Guide 

117

 

Pre-assembling the frame 

 

Attach the frame brackets (position 5 in the illustration "View of the frame 
(completely assembled)") on the left (1) and on the right side (2) using two 
round head screws M4x6 each. 

 

 

i

 

 Before the frame can be mounted, you must ensure that the cover 

angle (3) is moved as far as possible in the direction show by the 
arrow (6). If this is not the case, loosen the four laterally screws (4) and 
the two upper screws (5). Push the cover angle (3) as far as possible 
in the direction of the arrow (6). Fasten at least one of the previously 
loosened screws on right, on the left and on top. 

 

Summary of Contents for CINEO C4080



































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands