manualshive.com logo in svg

Wincor Nixdorf CINEO C4080, Installation Manual

Share
Download
Wincor Nixdorf CINEO C4080 Installation Manual Download Page 176

Check list

 for installation preparations for self-service systems

 

Appendix

 

164

 

CINEO C4080 - Installation Guide 

01750223447 D 

General information 

Installation 

  in front of a wall  

through a wall 

 free-

standing 

  encased 

 

 

yes   no   OK 

Is the load carrying capacity of the floor sufficient 
according to the installation documentation? 

 

 

 

 

 

Is there floor heating in the installation area? 

 

 

 

 

 

Are there cavities in the installation area (cable 
duct, raised floor)? 

 

 

 

 

 

Is the operation and maintenance space 
sufficient? 

 

 

 

 

 

Is the equipment screened from external light 
(sunlight)? 

 

 

 

 

 

Is a video surveillance system to be installed? 

 

 

 

 

 

Is a door opener system to be installed? 

 

 

 

 

 

Preparations 

Construction work 

 

yes   no   OK 

Is the securing of cash-dispensers in the raw 
concrete ensured (CEN standard)? 

 

 

 

 

 

Is the frame aligned and fastened in accordance 
with the installation instructions? 

 

 

 

 

 

Has a wall cutout that may be required been 
completed? 

 

 

 

 

 

Are the ambient conditions met? 

 

 

 

 

 

 

Summary of Contents for CINEO C4080



































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands