background image

Signal Booster

Installation

Guide

Mobile Wireless

Single Band

Signal Booster

Contents:

How it Works  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1

Before Getting Started  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2 

Installing a Wilson Electronics Outside Antenna  .  .  .  .  .  .  .  . 3

Installing a Wilson Electronics Signal Booster .  .  .  .  .  .  .  .  .  . 4

Installing the Low-Profile Antenna  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5

Powering Up a Wilson Electronics Signal Booster   .  .  .  .  .  . 6 

Warnings and Recommendations  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7 

Understanding the Signal Booster Lights   .  .  .  .  .  .  .  .  .  .  .  .  . 8

About Wilson Electronics  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9

Guarantee and Warranty  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 10

Signal Booster Specifications  .  .  .  .  .  .  .  .  .  .  .  .  .  .Back Cover

Wilson

®

         Electronics, Inc.

Note:  

This manual contains important safety and operating information . 

Please read and follow the instructions in this manual . Failure to do so 

could be hazardous and result in damage to your signal booster .

Summary of Contents for 801101













Reviews: