FIG. 2 -- SIDE SECTIONAL VIEW OF ENGINE
1. Fan Assembly
2. Water Pump Bearing and Shaft
Assembly
3. Water Pump Seal Washer
4. Water Pump Seal Assembly
5. Water Pump Impeller
6. Piston
7. Wrist Pin
8. Thermostat Assembly
9. Water Outlet Elbow
10. Thermostat Retainer
11. Exhaust Valve
12. Intake Valve
13. Cylinder Head
14. Exhaust Manifold Assembly
15. Valve Spring
16. Valve Tappet Self-Locking
Adjusting Screw
17. Engine Plate -- Rear
18. Camshaft
19. Flywheel Ring Gear
20. Crankshaft Packing -- Rear End
21. Crankshaft Bearing Rear Drain
Pipe
22. Crankshaft Bearing -- Lower
23. Valve Tappet
24. Crankshaft
25. Oil Pump and Distributor Drive
Gear
26. Connecting Rod Cap Bolt
27. Oil Float Support
28. Oil Float Assembly
29. Crankshaft Bearing Centre --
Lower
30. Connecting Rod Assembly -- No.
2
31. Connecting Rod Bolt Nut Lock
32. Crankshaft Bearing -- Front
Lower
33. Crankshaft Oil Passages
34. Crankshaft Thrust Washer
35. Crankshaft Gear
36. Crankshaft Gear Spacer
37. Timing Gear Cover Assembly
38. Fan and Generator Drive Belt
39. Crankshaft Oil Seal
40. Starting Crank Nut Assembly
41. Crankshaft Gear Key
42. Fan and Governor Drive Pulley
Key
43. Timing Gear Oil Jet
44. Fan, Generator and Governor
Drive Pulley
45. Camshaft Thrust Plate
46. Camshaft gear Retaining Washer
47. Camshaft Gear Retaining Screw
48. Camshaft Gear Thrust Plate
Retaining Screw
49. Camshaft Gear
TO START VEHICLE.
•
Release hand brake, if set.
•
Depress clutch pedal.
•
Move transmission gearshift leer to first speed position – see Fig. 3
(Note that the front axle and transfer case shift levers are not used when
the vehicle is driven on the highway in rear wheel drive.)
•
Depress the foot accelerator pedal gradually and at the same time,
slowly release the clutch pedal.
•
Allow the vehicle to gain momentum (two or three vehicle lengths), then
release the accelerator and depress the clutch at the same moment.
•
Move the shift lever promptly to the second speed position.
•
Depress the foot accelerator pedal gradually and at the same time,
slowly release the clutch pedal.
•
Shift to third or "high" speed in the same way at approximately 18 to 20
mph, releasing the accelerator and depressing the clutch before moving
the shift lever.
•
The synchronizing mechanism in the transmission makes gear shifting
silent and easy. This device adjusts the speeds of the two gears to be
engaged and prevents "clashin
TO CHANGE TO LOWER SPEED.
•
Depress the clutch pedal.
•
Move the gearshift lever quickly to the next lower speed, increasing the engine speed slightly, if traveling on level
road and release the clutch pedal.
•
It will be found advisable to make this change when the engine is placed under heavy pull, or when dropping down to
a very low speed, as when travelling up a steep grade, in sand or in congested traffic.
•
Never attempt to make the change with the vehicle traveling at a high rate of speed.
TO STOP THE VEHICLE.
•
Release the foot accelerator.
•
Depress the clutch pedal and apply foot brake.
•
When stopped, move gearshift lever into neutral.
•
Set the hand brake and release the clutch and brake pedals.
TO REVERSE VEHICLE.
•
With the vehicle at a standstill, depress the clutch pedal.