Wildfire HE900 User Instructions And Safety Download Page 24 | Manualshive

Page: 24 / 29

background image



24

FUEL BED LAYOUT

The following instrucons detail how the Rockwool, ceramic fuel bed and loose components are to be

installed onto the appliance. Great care should be taken when handling these ceramic parts as they are fragile

and can easily be broken. Do not force any component into posion, if it does not ﬁt easily then you are not

ﬁng the part correctly. These instrucons can also be followed to remove or reinstall the fuel bed aer

cleaning. This is a procedure that can be undertaken by the customer as required and the frequency will be

depend upon use.

See page 17 for glass panel removal and installaon.

Step 2

Fit the front ceramic rail strip in front of the burner as shown in the picture below.

Step 1

Fit place some of the Rockwool onto the surface of the burner in the posions shown in the picture

Step 3

Fit the large rear log A into the appliance as shown in the picture below.

«
...
22
23
24
25
26
...
»

Summary of Contents for HE900






























Reviews:

No comments

Related manuals for HE900

Brand: J. A. Roby Pages: 4

Brand: Martin Pages: 36

Retrofire RF24XBN

Brand: Valor Pages: 32

Brand: Vantage Hearth Pages: 40

Brand: Evonic Fires Pages: 44

Brand: Kingsman Pages: 17

Slimfocus mural

Brand: Focus Pages: 8

C11810LP Sedona

Brand: Real Flame Pages: 48

Brand: Napoleon Pages: 36

Brand: Valor Pages: 43

Brand: kozy heat Pages: 8

NADIA 14/P/BS/G

Brand: Kratki Pages: 32

Brand: Jensen Pages: 48

Brand: Warmington Pages: 8

Brand: Wamsler Pages: 84

FP-I-600BK Series

Brand: Landmann Pages: 56

Brand: Napoleon Pages: 14

Brand: Home Depot Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands