Wildfire HE900 User Instructions And Safety Download Page 28

Page: 28 / 29



Important Note:

The energy eﬃciency class of this product is deﬁned using a seasonal eﬃciency calculaon which reduces the actual

net eﬃciency of the product where the use of automated heat control, thermostats, window open sensors and

mers are not used. This is not to be confused with the net eﬃciency, or useful eﬃciency of the appliance (shown in

the tables above).

This product MUST be installed by a Gas Safe Registered Installer. Full details are provided in this manual.

Hearth Products Ltd. Unit 14 Tollgate Industrial Estate, Staﬀord, ST16 3SU

Product Fiche

Manufacturer : Hearth Products Ltd
Model No.

F-081XX2

Fuel Type

Natural Gas I2H

Energy Eﬃciency Class

Indirect Heang Funconality

Direct Heat Output kW

5.1kW

Indirect Heat Output kW

N/A

EEI

74%

Useful Energy Eﬃciency (NCV)

High : 83.0%

Useful Energy Eﬃciency (NCV)

N/A

Nominal Heat Output

High : 5.1kW

Nominal Heat Output

Low : 2.1kW

Heat Output Temperature Control

Two Manual Stages

Permanent Pilot Power (kW)

N/A

Space Heang Emissions NOx (GCV)

130mg/kWh

Summary of Contents for HE900






























Search results

Summary of Contents for HE900

Reviews:

Related manuals for HE900

Brands by name

Popular brands

Wildfire HE900, User Instructions And Safety

Search results

Summary of Contents for HE900

Reviews:

Related manuals for HE900

Brands by name

Popular brands