background image

INSTALLATION TYPE C 

These diagrams detail the installaon of the appliance into a Pre Cast Flue where a 

900 PRECAST MANTEL

 is being fied 

For details on 

900 PRECAST MANTEL 

crical dimensions see page 9. 

The 

900  PRECAST  SPACER  KIT 

is  used  to  create  an 

interface  between  the  precast  flue  and  the 

900  FIXING 

PLATE

.  Fit  the  hearth  and  firmly  aach  the  PRECAST 

SPACER to the wall.  See further details on page 12. 

 

Using  mortar  or  fondue  around  the  inside  edge  of  the 

SPACER/FLUE should be sealed and fixed into place as if it 

were a marble back panel. It is important that no leakage 

should occur. 

 

 

For minimum hearth requirements see page 9. 

 

The 

900  FIXING  PLATE 

is  then  screwed  to  the  900 

PRECAST  SPACER  with  the  screws  provided.  Using  fire 

cement  or  similar  around  the  inside  edge  of  the  joint 

between  the 

900  FIXING  PLATE 

and  the 

900  PRECAST 

SPACER

. Furthermore a suitable high temperature masc 

should be used to further seal around the outside edge of 

the 

900  FIXING  PLATE 

and the wall.  See further details 

on page 13 

 

It  is  extremely  important  that  both  the 

900  PRECAST 

SPACER 

and the 

900 FIXING PLATE 

are sealed to the flue 

as  essenally  a  complete  fireplace  opening.  Check  the 

integrity of the spacer and fixing plate installaon before 

proceeding. 

 

The TYPE C INSTALLATION is completed by installing  the 

900    PRECAST  MANTEL 

to the wall securely. The mantel 

should be centred around the 

900 FIXING PLATE

 

The crical dimensions of the 

900 PRECAST MANTEL 

are 

detailed on page 9. These crical dimensions ensure that 

the front trim plate of the fire and the front face of the 

mantel are aligned. 

 

The  front  trim  plate  of  the  appliance  is  fully  adjustable 

with  four  independent  magnets.  These  magnets  can  be 

screwed  in  or  out  to  posion  the  front  trim  plate 

correctly.  This  adjustment  is  provided  as  there  may  be 

some variaon in the wall flatness and level. 

 

See  page  17  for  full  details  regarding  front  trim 

installaon and adjustment. 

 

 

 

Ensure the hearth is set level before connuing with 

the installaon. Failure to install a level hearth could  

affect the installaon of the mantel and appliance. 

Summary of Contents for HE900






























Reviews: