manualshive.com logo in svg

White Mini-Seis III Pro, Operating Manual, Page: 2 / 49

Share
Download
White Mini-Seis III Pro Operating Manual Download Page 2

Mini-Seis III Pro™ Operating Manual 

Page 2 

 

Contents 

A Word Concerning This Manual .......................................................................................... 6 
Introduction .......................................................................................................................... 6 

Use .................................................................................................................................... 6 
Operating Modes .............................................................................................................. 6 
Ranges and Resolutions ..................................................................................................... 7 
Sample Rates ..................................................................................................................... 7 

Waveform Mode (4 or 8 Channel) .................................................................................. 7 
Waveform Mode (1 Channel) ......................................................................................... 7 
Histogram or Histogram/Waveform Mode (4 Channel) .................................................. 7 
Histogram or Histogram/Waveform Mode (8 Channel) .................................................. 7 

Waveform Recording Duration .......................................................................................... 7 
Battery Life ........................................................................................................................ 7 
Communication ................................................................................................................. 8 
External Data Storage ........................................................................................................ 8 
Accessories and Software .................................................................................................. 8 
Data Compression ............................................................................................................. 8 
Automatic Reporting .......................................................................................................... 8 
Options .............................................................................................................................. 8 

8 Channel ....................................................................................................................... 8 
GPS ................................................................................................................................ 8 
Ranges ........................................................................................................................... 8 
Non-Standard Sensors .................................................................................................... 9 
A Weighting ................................................................................................................... 9 
New Features ................................................................................................................. 9 

Connectors ........................................................................................................................ 9 
Connecting a Sensor .......................................................................................................... 9 
Communication ............................................................................................................... 10 
Charging ......................................................................................................................... 10 

The Keypad and Display ..................................................................................................... 11 

ON Key ............................................................................................................................ 11 
OFF key ........................................................................................................................... 11 
ENTER Key ...................................................................................................................... 11 

Summary of Contents for Mini-Seis III Pro


















































Reviews:

No comments