White Mini-Seis III Pro Operating Manual Download Page 19 | Manualshive

Page: 19 / 49

White Mini-Seis III Pro Operating Manual Download Page 19

Mini-Seis III Pro™ Operating Manual

Page 19

If using both linear and A weighting with separate microphones, it will be necessary to
reprogram the acoustic channel each time a change is made. Contact White if help is
needed.

Air Units

This field indicates the units that will be used to display acoustic data. Linear weighting
options are dBL (linear decibels), Mb (millibars), PSI (pounds per square inch) and Pa
(Pascals). A weighting uses dBA.

Air Range

This field value shows the maximum level that can be recorded. It is set at the factory and
can only be changed through the Seismograph Data Analysis software. Warning –the true
Air Range is determined by the hardware in the microphone, not the software. Setting the
software range to a value different from the microphone range will result in incorrect values.

Seismic Units

This field indicates the units that will be used to display seismic data. The options are IPS
(inches per second), and MMPS (millimeters per second). The units may be changed from
the UI. Changing the units automatically changes the displayed range.

Seismic Range

This field value shows the maximum level that can be recorded. It is set at the factory and
can only be changed through the Seismograph Data Analysis software. Warning –the true
Seismic Range is determined by the hardware, not the software. Setting the software range
to a value different from the hardware range will result in incorrect values.

-Use Factory Defaults-

This option replaces existing settings with factory default values.

-GPS-

Instruments equipped with GPS will display this option.

GPS
Loc:

+33° 04’ 0.51”

-96° 48’ 23.3”

Time:

17:43:56

Format:

D.MM.SS

Refresh: Startup
Time Sync: No

This display will show the GPS location coordinates in the selected format. The format
choices are D.MM.SS (degrees, minutes, seconds), D.MM (degrees, minutes) and D
(degrees).

The Refresh options are Startup or Record. The Startup option refreshes the GPS only when
the instrument is turned on or when the Sync Now soft key is used. The Record option

Sync Now

Home

Back

«
...
17
18
19
20
21
...
»

Summary of Contents for Mini-Seis III Pro


















































Reviews:

No comments