WhisperKool Phantom 3500 Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 39

background image

PH 080718

Page 18 | 1-800-343-9463

PRE-INSTALLATION WIRING

1. Remove the six (6) screws securing one of the center access panels on either side of the unit.

2. Insert a standard 18-5 thermostat wire through the small hole on the left side of the face plate as shown below, left.

3. Connect the 18-5 thermostat wire to the wires inside the unit as shown below. Connect the wires according to color:
green to green, blue to blue, yellow to yellow, and red to red. (The white wire will not be used.)

4. Replace the center access panel and re-secure using the six (6) screws removed earlier. Install a black strain relief around the

18-5 thermostat wire going into the unit as shown.

«
...
18
19
20
21
22
...
»

Summary of Contents for Phantom 3500








































Reviews:

No comments

Related manuals for Phantom 3500

Brand: Fakir Pages: 24

Brand: Bard Pages: 33

MWF-18CRN1-QC1G

Brand: Akai Pages: 40

AIR CONDITIONER SYSTEMS

Brand: DDB Pages: 12

Brand: Dimplex Pages: 12

Sky Air B-Series R-410A

Brand: Daikin Pages: 338

Brand: Daikin Pages: 132

Brand: MCS Pages: 68

OmniXAirFreshener

Brand: Mini Gadgets Pages: 20

Brand: BEEWAIR Pages: 20

Brand: UNITED Pages: 36

Brand: SPT Pages: 24

Brand: Sonnenkonig Pages: 64

Brand: GE Pages: 40

Brand: Daitsu Pages: 56

Brand: Olimpia splendid Pages: 270

SCE-AC13650B460V3

Brand: SCE Pages: 17

Brand: Daikin Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands