WhisperKool Phantom 3500 Owner'S Manual Download Page 34

Page: 34 / 39

PH 080718

Page 32 | 1-800-343-9463

TECHNICAL ASSISTANCE

WhisperKOOL Customer Service is available Monday through Friday from 6:00 a.m. to 4:00 p.m. Pacific Standard Time.

The appointed customer service representative will be able to assist you with your questions and warranty information more

effectively if you provide them with the following:

•

The model and serial number of your WhisperKOOL system(s).

•

Location of unit and installation details, such as ventilation, ducting, construction of your wine cellar, and room size.

•

Photos of the cellar and installation location may be needed.

Contact WhisperKOOL Customer Service

1738 E. Alpine Ave

Stockton, CA, 95205

www.whisperkool.com

Email:

[email protected]

Phone:

209-466-9463

US Toll Free:

1-800-343-9463

Fax:

209-466-4606

ACCESSORIES FOR COOLING UNITS

WhisperKOOL offers accessories to enhance and customize your wine cooling unit.

Condensate Pump Kit

The condensate pump kit is designed as an automatic condensate removal pump for water dripping out of our cooling units’

drain line. The pump is controlled by a float/switch mechanism that turns the pump on when approximately 21/4” of water

collects in the tank, and automatically switches off when the tank drains to approximately 11/4”. The condensate pump kit allows

the excess condensate to be pumped up to 20 feet away from the unit.

Phantom Ducting Kit

This kit allows either side of the unit to be ducted. Duct the cold air through a vent into the cellar, duct the hot exhaust air out of

the home. This option allows for total installation flexibility.

Note:

Flex or rigid ductwork is not included.

Accessories can be purchased at www.whisperkool.com

Summary of Contents for Phantom 3500








































Search results

Summary of Contents for Phantom 3500

Reviews:

Related manuals for Phantom 3500

Brands by name

Popular brands

WhisperKool Phantom 3500, Owner'S Manual

Search results

Summary of Contents for Phantom 3500

Reviews:

Related manuals for Phantom 3500

Brands by name

Popular brands