WhisperKool Phantom 3500 Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 39

background image

www.whisperkool.com | Page 19

Phantom Series

1. Locate the desired installation location.

2. Use a stud finder to locate the ceiling joists.

3. Place a piece of plywood atop the ceiling joists to support the unit's weight. Place the Ultimate Plus unit on top of the plywood

and make sure it rests securely.

4. Secure the unit to the ceiling joists according to state and local ordinances.

NOTE:

WhisperKOOL strongly recommends the use of a secondary drain pan with the unit. Install the drain line according to the

diagram on page 23.

INSTALLING THE UNIT IN AN ATTIC

Plenum

Ceiling joist

Plywood

«
...
19
20
21
22
23
...
»

Summary of Contents for Phantom 3500








































Reviews:

No comments

Related manuals for Phantom 3500

Brand: Panasonic Pages: 18

Brand: Unitary products group Pages: 20

Brand: Unitary products group Pages: 32

Brand: KeepRite Pages: 36

Brand: Midea Pages: 84

Brand: EdgeStar Pages: 14

Brand: Parker Pages: 48

Brand: Salda Pages: 14

OTEC IEFC-D Series

Brand: Omega Pages: 12

Brand: MrCool Pages: 27

Brand: Venmar Pages: 20

Brand: CIAT Pages: 18

Brand: HiRef Pages: 16

Brand: Rasonic Pages: 24

Brand: Daikin Pages: 72

Brand: Daikin Pages: 28

Brand: Daikin Pages: 32

Brand: Daikin Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands