background image

www.whisperkool.com | Page 27

Phantom Series

UNIT OPERATION

Initial Start-Up

Set the thermostat to COOL and fan switch to AUTO. Lower 

the setpoint to the desired cellar temperature. (A temperature 

of 55°F is the recommended setpoint.) See thermostat 

instructions for details.  

Normal System Cycle

The thermostat should turn the cooling system on when it 

senses a temperature one (1) degree higher than the setpoint. 

See thermostat instructions for details.

Anti-Short Cycle

Most thermostats have a safety feature that will prevent 

the condensing unit from cycling on and off within a short 

period of time. During the anti-short cycle, the compressor 

will typically remain off for 5-7 minutes. See thermostat 

instructions for details. 

Fan Operation

If the fan switch on the thermostat is in the AUTO position, it 

will run only during the cooling cycle. If the fan switch on the 

thermostat is in the ON position, the fan will continuously run 

until the switch is set back to the AUTO position.      

Anti-Frost

Systems equipped with a 24V thermostat conversion kit do 

NOT

 have an anti-frost feature. To reduce the possibility of the 

evaporator coil icing up, avoid setting the thermostat lower 

than 55°F.        

NOTE: 

To ensure correct system operation, the 24V thermostat 

must be placed inside the wine cellar, preferably in a central 

location away from any airflow.

The cooling system is equipped with the hardware needed to support a 24-volt air conditioning thermostat (not included).  

Summary of Contents for Phantom 3500








































Reviews: