Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity User Manual Download Page 32

Page: 32 / 64

4-4

d) Disconnect the wire connectors from

the pressure switch terminals.

(23)

(22)

(11)

WH-BK

(21)

WH-BK

(13)

11.

To remove the water inlet valves:

a) At the rear of the top cover, remove the

two 5/16

″

hex-head screws from the

water inlet valves.

b) Remove the pressure switch from the

dispenser housing (see step 10a).

c) Remove the two 7/32

″

hex-head

screws from the dispenser housing.

Water Inlet Valve Screws

d) Remove the dispenser housing and

water inlet valves from the top cover
and position the cover with the wire
connectors facing you.

e) Disconnect the wire connectors from

the water inlet valve terminals.

f) Disconnect the green ground wire from

the water inlet valve bracket tab.

Dispenser

Housing Screws

g) Slide the water inlet valves out of their

mounting bracket.

RD-YL

2 PK

BN-RD

GN-YL

Electrical Shock Hazard

Connect green ground wire to ground
terminal.

Failure to do so can result in death or
electrical shock.

WARNING

Summary of Contents for LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Search results

Summary of Contents for LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Reviews:

Related manuals for LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Brands by name

Popular brands

Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity, User Manual

Search results

Summary of Contents for LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Reviews:

Related manuals for LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Brands by name

Popular brands