background image

INSTALLATION

EN

 

• 

The cooktop must be set into a worktop between 30 mm and 60 mm deep.

• 

Install a separator panel under the hob.

• 

The lower part of the product must not be accessible after installation.

• 

Do not fit the separator panel if an undertop oven is installed.

• 

The distance between the underside of the appliance and the separator panel 

must respect the dimensions given in the figure.

• 

In order to ensure the correct operation of the product, do not obstruct the 

minimum required clearance between the hob and the top of the unit (min. 5 mm).

• 

If an undertop oven is installed, make sure the oven is equipped with a cooling system.

• 

For built-in dimensions and installation see the picture in this paragraph.

• 

A minimum distance must be maintained between the hob and the hood above it. Please refer to the user manual of the hood for more informations.

• 

Do not install the cooktop near a dishwasher or washing machine, so that the electronic circuits do not come into contact with steam 

or moisture, which could damage them.

• 

To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of the appliance.

PLACING THE HOB

Apply the supplied gasket to the cooktop (unless it has already been fitted), after having cleaned its surface. After the electrical connection (see the 

chapter “Electrical connection”), position each fixing clips on the dedicated slots on the lateral sides of the hob as shown in the picture. Then push 

the hob inside the cut out and check that the glass is flat and parallel to the worktop. The fixing clips are designed for every type of worktop material 

(wood, marble, etc.).

4x

2

1

3

DIMENSIONS AND DISTANCES TO BE MAINTAINED

 

Min. 40 cm

L

Min. 5  cm

Min.10 cm

i

Min. 5 mm

483 mm

742 mm

30    mm

+1 0

770 mm

 

510 mm

 

52/54 mm

R = Min. 6,5 mm

Max. 8 mm

 

490      mm

750      mm

0

+2

0

+2

Min. 50 mm 

 6-7 cm

min. 20 mm

min. 5 mm

57

75

80

Summary of Contents for ACM938BA










Reviews: