EASY 6000
– Issue 02
17
FAS INTERNATIONAL S.p.A. Via Lago di Vico, 60 SCHIO (VI)
– tel. +39 0445 502011 – fax +39 0445 502010 - e-mail: [email protected]
E
N
G
L
I
S
H
8.2.1
ACCESS TO THE SUBMENUS
Command 01 Machine test:
This is used to carry out a functional test on the machine. When you type 01 followed by ENTER, the
message "Choose the test to carry out ... 1 or 2 or 3". When you select number 1, you set an automatic test
and the display will show “Column rotation x”. When the value is set at "1", the drums will rotate during the
test, while they will remain stationary if you set "0". The test will begin when you press ENTER to confirm the
last option. The test consists of opening and closing the delivery doors in sequence followed by rotation of the
drums where applicable. The test will stop as soon as an operating anomaly is detected and the
corresponding error code will appear on the display.
Test number 2 tests the opening/closing of the delivery doors manually by means of the selection buttons.
Test number 3 lets you check and adjust the distance between the zero position sensor of the drum and the
corresponding magnet. When you press 3 followed by ENTER, the message, “Zero position sensor
adjustment”, will appear on the display and all the magnets installed on the drums will position themselves in
correspondence with the associated sensors. At this point, check the distance which must be between 2 and
3 mm and adjust if necessary. The function stops automatically when any selection button is pressed. Wait
until the drums have returned to the zero position and the "Choose the test to carry out" message appears on
the display again.
N.B.:
Command 66 must be set at 0;
Command 67 must be set at 1.
Command 02 Calls submenu for setting the clock & daily timers:
Key in 02 and press the ENTER pushbutton to enter the submenu for setting the clock and daily timers.
Alarm 00 will appear on the display. Follow the method described in the specific section to display and alter
the parameters.
Command 03 Setting the prices (also see Command 69)
:
Type 03 and press
ENTER
to go to the price setting submenu; "Drum number 00"
will appear
on the display.
Enter the number of the drum in which you want to change the price and press ENTER. The price appears on
the display. Enter the new value and press ENTER once again to save it or ESC to return to the main menu
without saving the changes.
Programming the value of the full prices changes the value of the corresponding discounted price and equals
them. Therefore, if you sell at differentiated prices, namely with a discount, you must first program the full
price and then the discounted price and never vice-versa, or just one of the two.
MULTIPRICE
If command 58 is set at 2 (2 prices for each drum) or 3 (3 prices for each drum) the machine
works by price line.
When you set 2 prices per drum (ref. Command 58), each drum will be divided into 2 equal sections.
Products sold at two different prices can be inserted into the same drum. If you choose 3 prices per drum,
products sold at three different prices can be inserted into the same drum. The tables below help to associate
each drum compartment with the corresponding price line:
Section 1
Price no.
Section 2
Price no.
Section 3
Price no.
drum
1
1
9
17
drum
2
2
10
18
drum
3
3
11
19
drum
4
4
12
20
drum
5
5
13
21
drum
6
6
14
22
drum
7
7
15
23
drum
8
8
16
24
If the drum is divided into 2 sections, consult the first 2 columns of the table for the prices, while if the drums
are divided into 3 sections (3 prices per drum) all 3 columns of the table are used.
Summary of Contents for Easy 6000
Page 1: ......
