Western TransCube 05TCG Operator'S Manual Download Page 25 | Manualshive

Page: 25 / 48

background image

17

3.

Securement for Trans-
port:

The frame is designed

with brackets on the top

corners to anchor the

tie-downs when trans

-

porting. Do not transport
TransCube unless it is

securely tied-down to the

vehicle frame.

The TransCube must be
securely attached to its
means of transport, be it

a custom trailer, ﬂat-bed

trailer or skid.

Fig. 7 MOUNTED ON CUSTOM TRAILER

Brackets

Schematic

Trailer

«
...
23
24
25
26
27
...
»

Summary of Contents for TransCube 05TCG

















































Reviews:

No comments

Related manuals for TransCube 05TCG

Brand: Taylor Pages: 70

Brand: Raith Pages: 26

Brand: Kane Pages: 16

Brand: Makita Pages: 17

Brand: Makita Pages: 13

Brand: Eaton Pages: 16

Brand: Eaton Pages: 15

Brand: ICP DAS USA Pages: 45

Brand: IFM Pages: 175

Brand: IFM Pages: 5

Brand: Land Pride Pages: 38

Brand: Nellcor Pages: 161

OXIMAX N-600X Series

Brand: Nellcor Pages: 210

Brand: Oase Pages: 120

Brand: OAKWORKS Pages: 24

Brand: UEi Pages: 5

Brand: UGO BASILE Pages: 47

Brand: UFO Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands