Western TransCube 05TCG Operator'S Manual Download Page 39

Page: 39 / 48

Pump will not run.

No power.

Connect power wires to 12 volt
power source.

Pump

off.

Turn

pump

on.

Diesel fuel in interstice.

Loose ﬁtting.

Tighten ﬁtting.

Leaking

coupler. Replace

coupler.

Over

ﬁlling

tank.

Watch

fuel

gauge

when

ﬁlling.

not

over

ﬁll

tank.

Water in the interstice.

Leaving latch lid open

Keep latch lid closed.

weather.

6 TROUBLE SHOOTING

The TransCube is a double walled tank for transporting diesel fuel from one location to another. It is a

simple and reliable system that requires minimal maintenance.

In the following section, we have listed many of the problems, causes and solutions to the problems that

you may encounter.

If you encounter a problem that is difﬁcult to solve, even after having read through this trouble shooting
section, please call your local Western distributor or dealer. Before you call, please have this Operator's

Manual from your unit and serial number ready.

PROBLEM

CAUSE

SOLUTION

Summary of Contents for TransCube 05TCG

















































Search results

Summary of Contents for TransCube 05TCG

Reviews:

Related manuals for TransCube 05TCG

Brands by name

Popular brands

Western TransCube 05TCG, Operator'S Manual

Search results

Summary of Contents for TransCube 05TCG

Reviews:

Related manuals for TransCube 05TCG

Brands by name

Popular brands