manualshive.com logo in svg

Wenzel HT 400, User Manual, Page: 5 / 30

Share
Download
Wenzel HT 400 User Manual Download Page 5

Control Panel - User Manual

2 - Safety regulations

Doc.no.: UM-22031

Revision: D

Page 5 of 30

2. Safety regulations

WARNING

For reasons of safety:

Independent modifications to the HT 400 (RC) control panel are prohibited.

Repair and trouble-
shooting

Repair work, trouble-shooting and fault rectification may only be car-ried out by
qualified technicians (e.g. an electrician).
It is essential that the connecting cable is separated from the control-ler before
the control panel is opened.
Plug connections may only be plugged in when the machine is switched off.

NOTE !

Do not move Joystick when switching on HT 400 (RC).

WARNING

During operations the antenna (only HT 400 RC) is not to be screened by a
hand or any object!

Disposal

Defective devices which cannot be repaired must be disposed of in an envi-
ronmentally responsible way. Therefore separate the individual materials (plastic,
metal, electrics) and hand these over for recycling.

2.1. Safety Test

WARNING

For safety reasons, it is vital that the EMERGENCY STOP button on the
control panel is actuated at least once a week. It must be estab-lished
when pressing the EMERGENCY STOP button that the circuit has been
interrupted.
With the wireless variant, this EMERGENCY STOP button test needs to be
carried out at both the control panel and base station.

Summary of Contents for HT 400































Reviews:

No comments