manualshive.com logo in svg

Wenzel HT 400, User Manual, Page: 16 / 30

Share
Download
Wenzel HT 400 User Manual Download Page 16

Control Panel - User Manual
5 - Basic functions of the control panel

Page 16 of 30

Revision: D

Doc.no.: UM-22031

5. Basic functions of the control panel

The basic functions described here can only be carried out when the con-troller
has been initialised.

Basic setting

When the controller is switched on, the control panel has the following initial
setting:

Axial control is switched off

Rapid traverse rate is switched on

Alignment of the control panel to the measuring machine: Operating position
= facing the Z-axis (also see Fig. 4.2)

NOTE !

Speed-setup (see Chapter 4) must be done manually.

5.1. Powering up HT 400 RC

Switch-on: Press switch-on button.

Battery mode: On-off switch position 1
24 V - Mains: On-off switch position 0

For charging battery or cable use plug in powercable from base-station or external
power-supply.

NOTE !

Base-station is active when WPC 20XX is powered up. With HT 400 RC
switched on, system is .negotiating. to set up a proper link. This will take
approx. 30 sec. And is indicated by a blinking LED of F1-key.

Summary of Contents for HT 400































Reviews:

No comments