manualshive.com logo in svg

Wenzel HT 400, User Manual, Page: 24 / 30

Share
Download
Wenzel HT 400 User Manual Download Page 24

Control Panel - User Manual
5 - Basic functions of the control panel

Page 24 of 30

Revision: D

Doc.no.: UM-22031

5.11. Modified functions of the HT 400 Design control panel

Adjusting mill cutter speed

Only when the mill cutter is active can its speed be changed.

Press the “Active key” to change to the Joy-mode

Press “C” button

Orange LED, top right in the key zone, lights up

mill cutter active

Turn the speed adjustment knop to set the speed required

Operating drive coupling and axial brakes.

WARNING

Ensure that the joystick is not extended before pressing the “Servo-on”
button. Otherwise the axes could move in an uncontrolled fashion.

Press “Servo-on” button

The supply voltage for the servo-drives is switched on.

Use the application software (CM) to start the joystick mode.

The X, Y and Z axes are activated (LEDs at the top right in the appro-priate
key zone are illuminated).

The axle drives are engaged and the X, Y and Z brakes are not being applied.

Deactivate the required axies: Press the buttons for the

appropriate axies..

Drive coupling is not applied and the brake of the axis in question is active
(locked). The LED in the respective axis button blinks.

Press the “Shift key” and then the required axis button

as well.

The respective brake is activated and the LED is extinguished.

Summary of Contents for HT 400































Reviews:

No comments