background image

P5/12

M12 Connector

 

5 male pins

CONTINUOUS

 MODE :

2

4

1

+ 24 V

3

GND

5

DIM 0-10V

STROBE

NPN

STROBE

PNP

black

brown

blue

grey

white

+ 24 V

1

2

3

4

Ground
PNP

+ 24 V
NPN

1

2

3

4

Ground

or

5

Dim 0-10V

5

Dim 0-10V

+ 24 V

1

2

3

4

Ground
PNP

5

Dim 0-10V

STROBE 

PNP

 :

+ 24 V
NPN

1

2

3

4

Ground

STROBE 

NPN

 :

5

Dim 0-10V

eMC IMMuNIty CONNeCtIONS: for greater 
EMC immunity when using the light under Strobe 
operation, configure the signal connections as 
illustrated here.  For Dimming, the Pin (5) should 
be connected to a voltage between 0V and 10V to 
ensure light output is correctly configured.

The  M12 male connector 5 points is COM-

pLIaNt with the M12 female connector 4 points. 
In that case, the dimming option is not available.

Strobe Mode

pNp : from 5 to 24V for 100% oN. From 0 to 4V for 100% oFF.
NpN : less than 2V for 100% oN. Above 2.2V for 100% oFF. Max 24V.

Strobe trIggerIng Mode - pnp and npn

CoNNECTIoN: M12 5 MaLe pINS CoNNECToR

pOwer SuppLy

  

StrOBe

  

DIMMING

+ 24 V
+ 24 V

1

2

3

4

Ground
PNP

5

Dim 0-10V

STROBE 

PNP

 :

+ 24 V
NPN

1

2

3

4

Ground
Ground

STROBE 

NPN

 :

5

Dim 0-10V

Summary of Contents for LMRX Series













Reviews: