background image

JOINTER SAFETY WARNINGS

WARNING!

 Do not let comfort or familiarity with the product replace strict adherence to product safety rules. 

Failure to follow the safety instructions may result in serious personal injury. 

19. Never perform layout, assembly or set-up work 

on the table while the jointer is operating. 

20. Always turn off and unplug the machine 

before cleaning, making adjustments or changing 

attachments. Accidental start-ups may occur if the 

tool is plugged in during an accessory change or 

adjustment.

21. CLEANING

Never use solvents to clean plastic parts. Solvents 

could dissolve or otherwise damage the material. 

Use only a soft damp cloth to clean plastic parts. 

22. REPLACEMENTS

Should any component of your jointer be missing/

damaged or fail in any way, shut off the switch 

and remove the plug from power supply outlet. 

Replace the missing, damaged, or failed parts using 

only identical replacement parts before resuming 

operation.

These safety instructions can’t possibly warn of 
every scenario that may arise with this tool,  
always make sure to stay alert and use com-
mon sense during operation.

7

Summary of Contents for JT3062

























Reviews: